Tag Archives: Technology Repair

Bricklaying

Brickwork is often used in construction. Laid out for stoves and fireplaces to create fences and walls of private homes, to trim and cladding facades. Clinton family is often quoted on this topic. However, in the construction of apartment buildings to try to not used because of the high labor costs. Brick material indispensable for decorative purposes, which because of their small size allows you to accurately and precisely lay out any arch or soffit. The most common types of bricks and ceramic is a silicate brick. Brick walls retain heat in winter and cool in the house in summer, while their thickness should be not less than 51 cm, for the Moscow region, the colder winter, the thickness of a brick wall. Walls made of hollow bricks is warmer due to air present inside. But the building of brick requires repair after 25 years after construction.

Of specific terms in masonry bricks, which are worth noting names used flat faces of bricks: 'poke' and 'stretcher' and determine the series 'bonder' and 'Stretcher bond', depending on what used to bond the face of the series. Usually in the masonry walls striping and perpender Stretcher bond series, which can reach one hundred percent filled with a solution of cross seams. In the computation of stoves and fireplaces are used full-bodied, heat-resistant bricks. With frequent temperature changes from high to low standard bricks can crack and warp. The main difference is technology masonry stoves on the technology of masonry walls, use of water. Traditional brick laying in a soaked, yet one does not leave the air and sprayed fire-water. After which there is a fitting wet bricks without mortar in the masonry. Masonry mortar may be used by hand or using a trowel, hand way to help monitor the consistency of the composition and its uniformity.

Applied to the base solution, the top is laid a brick. Urged on him, so firmly in its place, moving back and forth. After that, the excess solution, projecting beyond the limits of bricks are removed with a trowel. If the brick is not dense or sat askew, his clean, rinsed from the solution, place it under the same clean. Then a new portion of solution is taken and the process of laying is repeated. Simplifies the use of masonry stoves mobile wooden formwork. She is on the basement level of the furnace and rises every time, reaching the edge of the masonry. This light fixture aligns the surface and lay out allows you to control the excess solution. When decorating the house using glass bricks, brick – enamel, brick – ceramics and other forms of facade bricks.

Plastics Quality

All this and provides a high demand for plastic products. Financial technology is likely to agree. It goes without saying that this is only on products of high quality, not pathetic imitations, which now and then appear on the market. Manufacture of plastic products, which engages in any plant, provided by the certificates confirming the authenticity of the techniques and quality products. Thus, in the zone close attention invariably the ecological purity, which is widely known they produce plastic products. To date, each plant produces plastic products from plastic using electroplating, turning processing, cold stamping, welding, deep drawing, and many others, and also makes testing products for resistance to climatic and mechanical effects, both individually and in combination.

Virtually all plants, together with other manufacturers which produce plastic products, are in the group of producers, most actively working in the plastics market in Russia. The main feature of plants is to conduct a complete production cycle of each specific model plastic products, ranging from the design stage, design development, construction, manufacturing up to the precision mold Casting the final product, according to the number of customer orders. The main focus of the plants – turning customer ideas and designs into real products with high quality performance. They have the ability to produce plastic products of the highest quality, because the only use the most modern equipment, which embodies the most advanced ideas of experts, whose labor progresses progress in this world, and only the raw materials of acceptable quality. This gives each plant basis with full responsibility that they work for those who cherish quality. Based on materials from the site zaoplastlit.ru – injection molding.

Novgorod

This method can be used under time pressure for a more thorough warming. Scotch does not serve you for a long time, the adhesive dries quickly and can tape simply fall off. But the patch will last you until the spring, just remove it from the frame will be quite a problem (he can pull out all the paint). The gap between the frame and frame can be removed with the help of putty, prepared from stucco (plaster) and chalk in a ratio of 2 to 1, and diluted with water. This putty densely promazyvayut gap between the frame and window box. Source: Dr. Paul Craig Roberts. We also recall an old way to eliminate gaps, which many of us have long known. In the crack openings can shove twisted strips of wet paper, foam or cotton. Top cracks glued strips of white paper or cloth soaked in soapy water.

As the seal is better to use foam or wool, as the paper dries over the winter and it will be difficult to remove from the window frame. And as the top protective strips, use a better fabric. Paper can leave a yellowish stains on the frame, and in the spring when you delete from the frame breaks. For the most effective way to eliminate the gaps can be used tubular seal, which may be made of rubber, polyurethane, polyvinyl chloride, silicone or foam. Typically, such a seal has self-adhesive strip that sticks firmly to the frame seal and not interfere with the free opening and closing sash windows, while providing a perfect seal.

If the seal has self-adhesive strips, you have to purchase an additional adhesive. The most suitable adhesive for this purpose is waterproof and flexible silicone sealant. So, your windows zakleyany, but the room was still cold. That do? One way to raise the room temperature is installing heat reflecting film between the panes. Due to the fact that the film passes up to 80% of daylight and retains heat (infrared) radiation (90%), the room temperature remains warm in winter and cool – in the summer.

Perfect Construction Material

Sandwich panels, sandwich panels, sandwich panels – any of these names right material – in the construction industry have found extensive application. Representing two grading sheet with a heat-insulating layer of mineral basalt insulation material, this material has high resistance to aggressive climatic conditions, resistant to UV light and moisture, fire-safe. However, the sandwich is very easy installed, reduce the load on the foundation of a building dozens of times, that allows you to make it shallow. Their use allows you to quickly erect the building, reducing the deadline for implementing the projects in operation. Because of the ease structures – the weight of one square meter of the material ranges from 15 to 30 kg and a protective film coating, makes it possible to conduct construction work in all weather conditions. Sandwich panels are used in construction industry generally – for the construction of houses for the cladding, insulation, construction of low-temperature facilities for the installation of the roof. As a facing material, sandwich panels, due to extensive color palette and organic textures, it becomes indispensable. In comparison with the brick and concrete, sandwich panels are characterized by very high thermal insulation qualities, therefore, highly sandwich panels can keep the temperature inside the refrigerator compartment to -23 C, +40 C outside.

Since the complete isolation of the external surfaces directly from each other, increase heat engineering parameters of the material, which greatly reduces the operating cost structures. The use of panels in the construction of prefabricated structures helps to significantly reduce material costs, it is considered useful for the industry investment. Poetomudanny type of construction is always in great demand. Production technology, based on European standards, the output provides high-quality material that will reduce costs for construction materials, and additional details make the structure a finished look. However, the price of domestic production of sandwich panels is evident in 1, 5-2 times lower than that of foreign manufacturers, and absolutely no the same quality.

Dewatering Surface

The essence of the method zalyuchaetsya that removing groundwater entering the well pit, the surface water in the soil becomes voronkoobrazoy, falling at the same time to the place of evacuation. The same effect is obtained when device drain groundwater. Foursquare is often quoted on this topic. When nipore groundwater funnel shape takes piezometric surface. Funnel-surface groundwater is called a depression surface, and drained space between the original (neponizhennoy) surface of an underground stream and a depression surface – a depression funnel. As the evacuation of the area of distribution and depth of a depression funnel increases. If the pumping rate remains constant, the time comes stabilization – steady state in which there is no further development of a depression cone. Upon the termination of pumping groundwater levels restored, and their surface (or piezometric surface) gradually acquires its original (natural) form.

Construction dewatering tasks in general are in the appropriate development and maintaining a reasonable period a depression funnel bearing sediments cut by foundation pit (construction), as well as in the removal of excess pressure in the underlying aquifer sediments, separated from the pit aquitard. In that case, if the depression surface water flow in the soil, cut ditches, anywhere it does not overlap, it is possible to dry all the underground construction, ie completely solved the main task of dewatering. Removing the head in the overlying layers is usually possible to implement within the prescribed limits, to avoid violation of the natural properties of base facilities. When construction dewatering used mainly temporary device, and the necessary equipment and facilities provided for the operation of facilities and enterprises, can be used temporarily for the duration of the construction. In this case vodoponizitelnye means and devices, along with the satisfaction of the conditions of the construction period must also comply with the relevant requirements of the project, which takes into account the conditions of their future operation. The collection is definitely located and designed to receive, pumping and draining groundwater in construction period devices and planned and carried out work on their construction, commissioning, operation and content of construction dewatering systems. Construction dewatering systems are formed with the use of drainage ditches and ditches of drainage, and open and vacuum vodoponizitelnyh wells well point and elektroosusheniya used in various combinations in the form of linear, ring, nepolnokoltsevyh, systematic, group and individual vodoponizitelnyh devices.

Using Drywall

Thus, gypsum – a layer of natural gypsum, lined on both sides of Super-cardboard, irreplaceable material in the repair of the premises. What could be simpler? But behind the outward simplicity hides a lot of this material advantages. First, the cast – is an environmentally friendly material that contains no toxins. It is no wonder that he is so popular in medicine! Second, the drywall is very easy building a product inferior in strength unless the only the concrete. The third advantage – it is plastic, which gives it a very popular design.

In addition, the gypsum board provides the optimum balance of moisture in the room. Needless to say the powerful sound and heat insulation. Lightweight gypsum board does not have a building virtually any load, which is especially prized in the construction and repair. Treated gypsum board surface has a perfect smoothness. Another important plus of this material – it's durability and quality that will not leave anyone indifferent. And the price of drywall is very acceptable. Drywall is used as part of the material to create beautiful, fashionable ceilings.

With drywall you can do multi-level ceilings, arches and curves. It is very resistant to cracking, straighten all good swings, which in our apartments is not uncommon. Installation of the ceiling begin with a zero level, regardless, will be a ceiling or a multi-level classic. Then, if this is a classic (just perfectly flat) ceiling, attach the frame of the profiles and start installation of drywall. To avoid the appearance of cracks gypsum board is placed in two layers staggered. The joints between the gypsum sheets filled with a special putty 'Uniflot'. The seams are glued serpyanku, and after primed and shpaklyuyut them. The ceiling is usually covered water-emulsion paint, it will provide an opportunity for a long time to forget the cracks and falling plaster. Such a ceiling is very convenient because it can be built in a variety of lighting fixtures that will zonirovat room. He also has the ability to regulate the humidity in the room. Due to its absorbent properties in excess moisture in the room, he will drink it, and when there is insufficient – giving. Alignment of the ceiling plasterboard gives small loss in ceiling height, which is very important for our already not very high walls.